By John. Ceiling Fan. Published at Friday, August 17th, 2018 - 18:55:47 PM.
Outdoor Ceiling Fans If you are planning on installing a ceiling fan in an outdoor location, it is important to purchase a fan that is designed specifically for that purpose. If you install an indoor fan in an outdoor area it is likely to short out (which can be hazardous) or simply break down prematurely. Outdoor ceiling fans are designed differently than indoor ceiling fans because they need to be able to the forces of mother nature. Here are some of the ways that outdoor ceiling fans differ from those made for indoors: The decorative motor casing is either sealed or designed to prevent water or moisture from coming in contact with the actual motor inside. The wiring is a higher grade with additional shielding. Screws and other components are typically made of stainless steel. The finish on the motor casing and hardware is usually a weather resistant powder coat, stainless steel, or has some additional protective coating that can handle exposure to the elements. The blades are likely made of ABS plastic rather than plywood. ABS is a very strong durable material that resists warping and discoloration from moisture or UV exposure. Light fixtures are sealed on top and designed for outdoors The mounting hardware is either water tight or designed to prevent water from entering from above. There are 2 types of outdoor ceiling fans, those rated for DAMP locations and those rated for WET locations. There is a notable difference between the two and it is important that you choose the right type for your application. In either case, make sure the fan you purchase is UL Listed for the application you need so that you know it can be safely installed without creating a potential electrical hazard. Here are the differences between the two types of outdoor fans: Damp rated outdoor fans are designed to handle moisture but not direct contact with rain or running water. Therefore, a damp rated outdoor ceiling fan can be installed in a covered area such as a patio or screened in porch or other areas that are protected from rain or dripping water. Wet rated outdoor fans are designed to handle direct exposure to rain. They can be installed in virtually any indoor or outdoor location, covered or uncovered. So you can install a wet rated outdoor ceiling fan in an open gazebo, lattice covered lanai or other similar shade structure as well as under a covered porch or patio. Because wet rated outdoor fans are pretty much water tight, you can actually clean them by hosing them off...which is a great reason to buy a wet rated fan even if all you need is a damp rated model. Commonly asked questions about outdoor fans: Can an outdoor ceiling fan be installed indoors? Yes, you can install an outdoor fan in your living room or any other room in your home where you want a fan. Many people will do this simply because they like the look of a particular outdoor fan. Also, outdoor fans are highly recommended for laundry rooms and bathrooms or any other room inside your home that that tends to have excessive moisture. In more humid climates, outdoor fans are a great choice for every room in the home. I live in a very windy area and have had problems with blades breaking off...are there any outdoor fans that are made to handle high winds? High winds can in fact sheer the blades off a ceiling fan, particularly cheaper models that use lightweight materials. Usually it is the metal blade holders that attach the blades to the fan that break rather than the blades themselves. So if you are in an area prone to high winds, outdoor fans that do not have blade holders are your best choice. If the fan is to be installed in an area that is 9 feet high or less, a hugger style outdoor fan is even better. A perfect example of such a fan is the Minka Aire Concept II Wet, which is one of the very few outdoor fans that meet this criteria. Are there any outdoor fans that are designed to be taken down easily or that have blades that are easy to take off when a storm is coming? This is a very common question. Unfortunately the answer is no. There are no ceiling fans designed with a "Quick Disconnect" mechanism or with blades that snap on and off. However, I suppose that if any fan manufacturer came up with such a fan it would be a big seller. Running wires and installing a junction box can be difficult in many outdoor applications. Are there any outdoor ceiling fans that are battery operated? Although DC powered ceiling fans are now in fact available, they are not yet powerful enough to handle the needs of outdoor applications, nor are they being designed to work from batteries. Currently, most DC powered ceiling fans use an AC/DC converter, so they still require electrical wiring. However, I would look for this to change in the near future...most likely in the next year or two. Can a remote control be added to an outdoor ceiling fan? Most add-on remotes or wall controls are not rated for use outdoors, so unless the control is specifically designed for the fan you are considering and is rated for the correct application (Damp or Wet), then you should not use it. If a remote control or wall control is important to you, look for outdoor fans that have such a control included with the fan. Can any light fixture be added to an outdoor ceiling fan? No. Just as ceiling fans are rated for Damp or Wet locations, so are the light fixtures that are used with them. Make sure you purchase a light fixture that is made by the manufacturer of the fan and that has the same rating. If you want an outdoor fan with a light fixture, your best bet is to purchase one comes with one, this way you can be certain they are compatible.
Hunter Ceiling Fan - Energy Saver Did you know that by using your ceiling fan year-round, it is possible to save as much as 40% off your air conditioning costs, and in winter, can save up to 10% on your heating bill? If this sounds good to you, it may be time to purchase one or more ceiling fans for your home. If you want to be sure you buy the best possible ceiling fan, Hunter ceiling fan is a high quality product. If you look for the symbol for Energy Star on select units, it means that the product you are about to purchase has met the Energy Star guidelines for energy efficiency. Select Hunter ceiling fans are also equipped with energy efficient 30-watt compact fluorescent bulbs and are California Title 24 Compliant. This means that a Hunter Ceiling fan is "quiet for life." You are sure to find a Hunter ceiling fan to suit each room of your home. There are many styles to choose from, like classic or modern. A Hunter ceiling fan, with proper care should last you a lifetime. Hunter ceiling fans are made from the finest materials to create designs that are stylish and will add beauty and warmth to any room of your home. Each Hunter ceiling fan has been designed and crafted to rise above other ceiling fans for quality and efficiency. You can be assured that your Hunter ceiling fan will be more than just a beautiful addition to your home. A Hunter fan has an exclusive motor technology and mounting system. This is to ensure that every Hunter ceiling fan will not wobble and will be whisper quiet. This is something that Hunter has been doing since 1886. When you purchase a Hunter ceiling fan, you will have the peace of mind knowing that your ceiling fan is backed by a limited Lifetime Motor Warranty. The WhipserWind motor is available for most models of Hunter ceiling fans, and it transports mega-powerful air movement. Combined with the whisper quiet performance of the Hunter ceiling fan, you cant find a better value. When you purchase your Hunter ceiling fan, it comes ready to easily install. You will have complete instructions on just how to mount your ceiling fan without worry or hassle. Your Hunter ceiling fan was designed with easy installation and maintenance in mind. If you think your ceiling is too high or too steeply angled, with Hunters vaulted ceiling mounts and extension downrods, you are almost sure to find a Hunter ceiling fan to fit your special needs. Before you purchase a ceiling fan, you should do plenty of research on the internet. Always keep in mind, all ceiling fans are not created equal. To ensure the highest energy efficiency and the best product for the job, choose a Hunter ceiling fan. You wont regret your decision.
Why Do Ceiling Fans Have a Reversing Switch? What is the reason for having a reverse button on ceiling fans? Well "they" say that you cannot stand a draft during winter months, but that you can equalize the air temperature buy using your fan in the reverse direction. I always wondered why the older ceiling fans did not have a reverse button. Were the people who designed those fans, just too stupid to think about using reverse in winter? During winter, when you use the central heating system, the warm air coming out of the registers, in each room, will naturally rise and because the registers are up high already, the hot air will build at the ceiling level and gradually work its way down toward floor level. The heating unit runs until the temperature is comfortable at the lower levels of the rooms. But by the time this happens, it will be very hot at the ceiling level. Many BTUs are wasting heating the ceiling areas of the home, where we dont live our lives. But what if there was a way to get this hot air down off the ceiling, to the lower levels where we live. The heating unit would not need to work as long and the savings on our utility bill could be significant. AHH CEILING FANS! will bring this air down and mix the hot air with the cooler air at floor level. This mixing would basically equalize the temperature at floor and ceiling levels, which means that the heat would not be wasted keeping the ceilings warm. The heating unit would not run as much. The utility bill will be lower while the comfort level will remain the same. But then someone said that the draft created by the ceiling fans would be too much for winter months. So someone else said "well, lets just reverse the ceiling fans and let the air blow up until it hits the ceiling and then it will go horizontal in all directions until it hits the walls. Then it will come down vertically until it hits the floor. Now it will travel, at floor level, back in toward the center of the room and then back up to the ceiling fan. What a genius! Now everyone can use ceiling fans to equalize the temperature without feeling a draft in winter. Oh yea! So what happens when this warm air starts down the walls and hits furniture, bookshelves, etc? It will start a horizontal movement toward the center of the room. Now when it comes out past the obstruction, will it turn and fall toward the floor, where it can mix? If warm air falls instead of rising, then I guess it could. What happens when air from the ceiling fans hits the ceiling in a room with a sloped ceiling? If the ceiling fan is centered in the room, it would be basically half way up the slope. So wouldnt all the air go directly up the slope from where the ceiling fan is mounted? What about the other half of the room? What happens when the room is large? Will the force, coming down the walls, still be enough to get this warm air to the floor, especially when the ceiling is two stories high? What happens when ceiling fans are in a room with a two story high ceiling, which is open to the second floor level of the home? Wouldnt the warm air go off into the second level, instead of coming down to the floor and in this situation, wouldnt the ceiling fan steal the warm air from the first level and take it to the second floor, defeating the purpose for which it is being used? On the other hand, if you blow the air down, the hot air at the ceiling level will be forced down to floor level where it will move in all directions toward the outer walls of the room. The air can now mix and seek its own level. The hotter air will naturally rise to the ceiling level where it will be picked up by the fan to repeat the cycle. So wouldnt this be much more efficient than using reverse, especially in the scenario where the ceiling is two stories high and open to the second floor? But what about the draft? I say just run the ceiling fan at a low speed or the highest speed that you can tolerate and still be comfortable. Could reverse on ceiling fans be a marketing tool to sell fans in winter? You decide. But I do not think that the old folks overlooked something as important as this. I think that they used what was most efficient. I agree and my ceiling fans always blow down, winter and summer. And if you happen to have a room with the two story ceiling where the room is open to the second level, and where you notice the upstairs is always hot while the lower level is cold during winter, try using your ceiling fans in the down direction. You will not believe the difference!
Ceiling Fan Frequently Asked Questions I. What is the purpose of a ceiling fan? A ceiling fan serves two purposes 1. To provide a breeze thereby creating the "wind chill factor" 2. To circulate the air throughout a room or area II. How do ceiling fans lower the temperature? They dont, at least not literally. Unlike an air conditioner, ceiling fans do not directly affect the air temperature. That does not mean, however, that ceiling fans are not effective in cooling. As pertaining to the two purposes listed in question (I): 1. The moving air from a ceiling fan will help you feel cooler regardless of the temperature of a room. It is much the same as being outside in the summer-- it can be 80-90 degrees, and if there is a breeze, it is very pleasant. 2. The circulation from a ceiling fan can disperse the cool air from lower areas (and air conditioning) into the central, inhabited areas of a room. IIa. How do ceiling fans help heat in the winter? Much the same as they help with cooling in circulation. Running your heat in the winter, hot air rises to the ceiling, and so much of the heat is wasted. Running a ceiling fan during the winter, to push down warm air from the ceiling and eliminate cold spots, can save a great deal of heating energy. III. What rooms should have ceiling fans installed? EVERY room. Depending on your personal preferences, any and every room can benefit from a ceiling fan installed. The more time people spend in a given room, the greater the benefit of a ceiling fan. For circulation, especially large rooms, and/or those with high and/or vaulted ceilings. People will have their preferences on where they most prefer the benefits, but ultimately any room is a good idea. IV. What size fan is needed for a particular room? Ceiling fans commonly come in two sizes: 52" for larger rooms and 42" for smaller rooms. Many companies offer 30-36" fans for exceptionally small rooms, and 56-60" fans for larger and/or commercial settings. The most common size by far is the 52" fan, which is typically appropriate for most rooms. V. My ceiling is lower, do I need a hugger fan? Hugger fans are designed to provide the minimum distance between the ceiling and the fan blades. This is ideal for lower ceilings as it provides the maximum clearance between the blades (and other lower parts of the fan such as lights) and the floor. The downside is that the shorter distance between the blades and the ceiling impedes circulation to a degree. Hugger ceiling fans are less effective than regular ceiling fans regardless of ceiling height. VI. My ceiling is higher, how long of a downrod do I need? For maximum circulation, the blades should be positioned 8-10 from the floor. However having the blades too far away from the ceiling can sometimes lessen the effectiveness of heat destratification. Not to having the blades 9 from the ceiling on a 15 ceiling may look a little imposing. VIa. I have a vaulted ceiling, do I need a special kit? Usually not. It is standard for fans to include hardware that will allow the fan to be mounted on a ceiling up to a ~30 degree incline. Hugger fans are not designed to be mounted on a vaulted ceiling. There are other rare exceptions, these are usually noted by the manufacturer and can be adapted. VII. What sort of control options are available? Most ceiling fans made in recent years have a built in three-speed pullchain control. Regardless of whether or not the fan is wired to a separate switch, you have full control of the fan from the chain. Off-high-medium-low. Most fans are also reversible and have a reverse switch built into the fan body. If the fan has a light, the light will have its own on-off pullchain. The entire fan assembly can be controlled without the benefit of a remote switch. Many companies now offer fans with remote speed control options that allow for independent fan and light control without additional wall switches and wiring. These can include wireless remote controls, replacement wall switches, and computerized options that involve one, the other, or both. This allows a fan to be installed in a conventional two-wire hookup and benefit from the control options of a 3 wire (two switch) hookup without installing a third wire. The mobility of a wireless remote and the features of the computerized controls are additional benefits. Ceiling fans with conventional pullchain controls can be retrofitted with remote speed control options such as those mentioned above. The retrofit kits include the wall or wireless remote control, and a receiver that is attached inside the ceiling fan canopy and wires between the fan and the power source. The receiver requires only a two-wire power source, switched or unswitched. VIII. How many blades is best? These days ceiling fans are available with any number of blades from one to eight, although any number below 3 and above 6 is for novelty or decorative purposes only. Most fans have 4 or 5 blades, some are adaptable to take either. Most people assume that more blades move more air, i.e. a fan with five blades moves more air than a fan with four blades. This, in fact, is incorrect. More blades results in a greater load on the motor, and a greater load on the motor causes it to operate at a slower speed. A fan with less blades operating at a faster speed will more more air than a fan with more blades operating at a slower speed. This is why most commercial fans have three blades and a high speed motor, to provide the greatest amount of airflow efficiently. IX. What are the quality differences between fans on the market? Many different fans are available these days, with a great degree of different options, styles, designs, and prices. Often times people buy a fan for appearance-based reasons. But most consumers, about to spend a significant amount of money on a ceiling fan (or fans) are concerned about getting the best quality product, or at the very least the best quality product within their price range. It is a commonly held theory that you get what you pay for: the more something costs, the better quality it is. As with many products, that is generally true with ceiling fans, but there are other factors. When you buy a ceiling fan you are paying for three things: 1. Quality and features 2. Design/style 3. Name recognition The most expensive fan may be the best quality, or it may be the most expensive design, or it may be the best known brand name. IXa. What makes a ceiling fan Energy Efficient? How do I consider this when choosing a fan? There are three factors: 1. How much air is moved 2. How much current is drawn 3. The quality and construction of the fan Obviously the most efficient ceiling fan would be that which has the best #1/#2 ratio. However #3 is also a very important factor in buying a ceiling fan, and just because a fan has the best ratio does not mean it moves the most air. A fan that draws very little power but moves very little air may be considered very efficient. Additionally, if the fan has a light kit, the light kit is much more crucial to energy consumption than the fan motor. Ceiling fans typically draw ~100 watts or less on the highest speed setting, however the typical four socket light kit draws 240 watts consistently. Much more important than finding the most efficient motor, in this case, is maximizing the efficiency of the light kit. Compact Fluorescent light bulbs are ideal for this purpose-- the same light kit will then draw 60 watts or less. X. Fan Operation: What speed and direction settings should be used? This is a very subjective topic, and for most it was probably answered by parts I & II above. There are a number of factors that vary by setting and situation-- fan location, ceiling height, fan model, and most importantly, what purpose is intended. A few suggestions that may or may not apply: 1. It is unlikely that a fan would be used on high except to create a significant breeze. When you wish to do so the fan would be used in the downdraft setting. Depending on how much of a breeze is wanted medium speed may also be acceptable. 2. For a gentle breeze and circulation, in most cases the fan would be used on low in the downdraft setting. 3. To destratify heat (and for circulation) the fan would be generally set to updraft mode in low or medium speed. Heat can also be recirculated with low speed in the downdraft mode, depending on which produces more of a notable breeze. XI. How effective are ceiling fans with heaters built in? The most important thing to remember about any electric heater is that they use a great amount of electricity. This includes ceiling fan heaters as well as space heaters, etc. They are available with a variety of different sizes and settings, but the average uses ~1000 watts. It is not wise to use an electric heater unless it is absolutely necessary, using a heater ceiling fan (for example) in conjunction with an effective furnace etc will NOT save energy. So it would be a fair assumption that you should only consider a heater ceiling fan in a situation where you would also consider an electric space heater or the like. XII. What is the use for a fan mounted outside, such as on a porch? What sort of fan is recommended? If a fan is going to be exposed to rain and snow and such, youll want to make sure it is sealed so water cannot get into electrical parts. If its not actually going to be getting wet, just somewhere exposed to changes in climate (a covered porch, etc) you generally look for a fan with a finish that wont rust and blades that wont warp. Many companies offer fans that are specifically rated for these situations. These fans will have Underwriters Laboratories certification for damp or wet locations. If a fan is going to be subjected to these conditions it is important that it is able to do so safely. XIII. Ceiling fan lights-- what options are available? Ceiling fans being used with light attachments have become more and more common as years progress. It is significantly easier to install a ceiling fan where there is an existing light fixture than where there is nothing, but if you are removing a light source you will need to replace it. As a result, the majority of ceiling fans sold include light kits already attached.
Any content, trademark’s, or other material that might be found on the LukeJohnsonPhoto website that is not LukeJohnsonPhoto’s property remains the copyright of its respective owner/s. In no way does LukeJohnsonPhoto claim ownership or responsibility for such items, and you should seek legal consent for any use of such materials from its owner.